How To Install Refrigerator Water Line? [ New 2020]

How To Install Refrigerator Water Line

How To Install Refrigerator Water Line? Purchasing new appliances throughout the vacation season is the thing to do if you need to receive the best prices. That new refrigerator you have been eyeing is now available, and you’ll be able to buy it without sorrow, knowing you have the best cost.

After establishing all of the delivery details, you wait for your new refrigerator at home. Picture this, your new fridge has been sent, and you have experienced the movers to place it around the place your old refrigerator occupied.

You start to hook up all of the cables so that you may set the food that you took from your old refrigerator into your new one. You then encounter a bit of a problem. Your previous refrigerator did not have a water filter; therefore, you are unsure when you’ve got a water line or whether you have to obtain a brand new one.

See more: Best Refrigerators Brands.

Before calling a plumber, it may be best to browse through this seven-step manual about the best way to install and run a water line into your brand new refrigerator. Measure one provides you a pep talk to psych yourself up for your project you did not know you’re going to achieve.

Measure two discussions about if you currently have a water distribution pipe accessible and what to do if you do not. Action three teaches you what needed-steps are. Four through seven ends up with the way to link everything.

Go forth and find out about all of the inner workings of water lines into fridges, then return here to answer one final question.

Required Tools for this particular fridge water line project

Required Tools for this particular fridge water line project

Have the essential tools for this fridge water line DIY project lined up before you begin. You will save yourself time and frustration.

  • Soldering torch
  • Tape measure
  • Tube cutter

You might also require a drill and a 1/2-in. The bit should you have to conduct the waterline via cupboards, as revealed here.

Required Materials for this particular fridge water line project

Keep away from last-minute shopping excursions by having all of your stuff prepared beforehand. Here’s a listing.

  • 1/2 in. Copper tubing
  • 1/4-in. Flexible aluminum tubing
  • Copper tee
  • Water supply stop valve

See also: How To Fix A Refrigerator?

How To Install Refrigerator Water Line

How To Connect Refrigerator Water Line?

When conducting a fridge water line, the largest challenge will be tapping into the chilly water pipe and operating the 1/4-in. O.D. (external diameter) flexible aluminum tube. It is possible to purchase ice maker installation kits in home centers and a few hardware shops, but we do not suggest them.

Most include a saddle valve (which does not meet the plumbing code in certain areas), and a few contain plastic tubing (which could dry, divide and flow over time). We urge more durable valves and aluminum tubing for superior water flow and a decreased risk of floods, resulting in considerable damage.

To begin, find the chilly water supply line closest to the fridge under the kitchen sink, beneath the ground, at the wall, or perhaps at the ceiling. In this kitchen, we conducted the new refrigerator water line from beneath the kitchen sink cabinets. (Notice: We eliminated the drainpipes to demonstrate this project).

Make sure you keep the tube above storage areas and supporting drawers when possible to prevent tube harm. Should you have to drill through walls or floors, check out air ducts, electrical wiring, plumbing, or other potential impediments.

Then compute the number of feet of 1/4-in. O.D. flexible aluminum tube you require for the fridge water line. Figure 6 to 2 ft. of additional coiled tubing behind the refrigerator, so it’s possible to pull it out for cleaning and support.

Then decide which among three fridge water line connection choices you may use: a standard tee fitting that’s soldered, a compression tee, or a saddle valve. Plumbers advocate removing a part of their cold water heater to fasten at a normal 1/2-in copper tee. In case you have CPVC (vinyl) or steel pipes, add tee shirts made of the identical material.

If you do not wish to solder, you can cut the aluminum water pipe and put it in a 5/8-in. O.D. compression instead (do not use them indoors walls since it is not secure and pipes code won’t let it). Insert pipe compound to the threads to make it much easier to tighten compression joints.

See more: How Cold Should A Refrigerator Be?

The least dependable alternative is a saddle valve created for 1/2-in. Copper tubing. It’s a tiny shutoff valve that utilizes a sharply pointed metal pole to pierce the pipe’s outer walls when screwed inward. You then back out the pole, and water flows through a small hole to the tube.

Some appliance installers state saddle valves operate, but most fridge makers advise that you drill a hole in the pipe to get superior circulation rather than employing the valve to pierce the gap, then attach the saddle valve (check your owner’s guide).

To start, shut the water off in the primary valve, then open the faucet and a different lower degree faucet to drain the pipe. Next, cut out a small part of this cold water line pipe and solder into a tee. Cut a 3- to 4-in.

A piece of aluminum pipe solder it in the tee below the sink, then solder a water supply stop valve on the opposite end. When the meeting has cooled, shut the lid and start the water main to look at the leaks’ fittings.

Then plan a tube path through all of the cupboards (avoiding sharp ends that could kink tube) and drill 1/2-in-holes as necessary between cabinets.

To sew coiled tubing (not the whole roster), have a partner hold the end of the tube flat on the ground, then push the roll from the ground when unrolling into the length you want to experience the cabinets. Now snake the tube in backward, beginning in the refrigerator, so the coiled section remains there.

Read also: How To Recharge A Refrigerator?

Then join the 1/4-in. Refrigerator water to the stop valve using a compression combined. Then attach the tube to the rear of the cabinets, each 2 to 4 ft. We are utilizing 1/4-in. Nylon wire/cable clamps.

As soon as you’re out of the previous cupboard, do not attach any clamps: run the tube into the ground close to the water line hookup on the refrigerator. However, do clamp the tube into the fridge.

Do not forget to flush out the tube by conducting a gallon of water during the new line into a bucket until you attach it to the refrigerator. To attach the hose to the fridge, follow the operator’s manual.

Ordinarily, the compression fittings include the refrigerator. Before you cut the tube to its final length, be sure to have 6 to 8 ft. of the coiled tubing, which will stay coiled and stored behind the refrigerator when you push it into position.

Make sure you cut on the end of the tube square. Then slide onto the compression fittings, then lubricate the threads onto the fridge fitting with pipe chemical and twist on the tube.

Significant: Hand-tighten the matching, then tighten three-quarters of a twist using a tiny wrench on either side of the pairing. When attached, start the brand new stop valve and examine the whole fridge water shuttle system for leaks.

Leave a Reply

Your email address will not be published. Required fields are marked *

We use cookies and other technologies on this website to enhance your user experience. By clicking any link on this page you are giving your consent to our Privacy Policy and Cookies Policy.